V. IS 800 2007 LSD - Pipe - Tension and Bending
The document verifies the design of a 3 m long cantilever pipe section (90 mm nominal bore, 3.6 mm wall thickness) subjected to 10 kN axial tension and uniform biaxial bending moments of 1 kN/m per IS 800:2007 limit state method, confirming the pipe's plastic section classification, slenderness ratio within limits, and axial tension capacities for yielding (251.8 kN) and rupture (297.8 kN) based on calculated section properties and steel material strengths.
V. IS 800 2007 LSD - Pipe - Tension and Bending
Verify the design of a pipe section subject to axial tension and biaxial bending per the IS 800:2007 limit state method.
Details
The member is a 3 m long cantilever subject to a 10 kN tensile force and uniform bending moments of 1 kN/m along both major and minor axes. The section used is a 90 mm nominal bore with a wall thickness of 3.6 mm (STAAD.Pro section designation PIP10106L) and is braced to prevent lateral-torsional buckling. The steel has a yield strength of 250 MPa, an ultimate tensile strength of 420 MPa, and a modulus of elasticity of 205×(10)3 MPa.
Validation
Section Properties
Outer diameter, OD = 101.6 mm
Wall thickness, t = 3.6 mm
Inner diameter, ID = 101.6 - 2 × 3.6 = 94.4 mm
Cross-section area, Ax=π4(101.62-94.42)=11.08 cm2Ax=π4(101.62−94.42)=11.08 cm2
Moment of inertia about both axes, I=π64(101.64-94.44)=133.2 cm4I=π64(101.64−94.44)=133.2 cm4
Radius of gyration about both axes, r=√I/Ax=3.47 cmr=I/Ax−−−−√=3.47 cm
Elastic section modulus about both axes, Ze=IOD/2=26.23 cm3Ze=IOD/2=26.23 cm3
Plastic section modulus about both axes, Zp=16(101.63-94.43)=34.6 cm3Zp=16(101.63−94.43)=34.6 cm3
Constants
- γm0 = 1.1
- γm1 = 1.25
Section Classification
ε=√250/fy=1ε=250/fy−−−−−−√=1
For circular, hollow tubes subjected to moment, OD/t = 28.22 < 42ε2 = 42
Therefore, the classification of the section is "plastic".
Hence, from Table 10 of IS 800:2007, the buckling class about both axes is "a".
Check Slenderness Ratio
ky = kz = 1
The maximum allowable slenderness ratio is 180.
Slenderness ratio about both axes, kzL / rz = 86.67 < 180
So the slenderness is within the limit.
Axial Tension Capacity
Check for yielding of gross section per Cl. 6.2:
Tdg = Ag × fy / γm0 = 11.08 × 250 / 1.1 = 251.8 kN
Check for rupture of critical section per Cl. 6.3:
α = 0.8
Tdn = α × Anet × fu / γm1 = 0.8 × 11.08 × 420 / 1.25 = 297.8 kN
Block shear areas are not specified and therefore not checked.
The critical tension ratio 10 / 251.8 = 0.040
Check Axial Compression
The non-dimensional slenderness ratio, λz=√fy(kzL/rz)2π2E=0.961λz=fy(kzL/rz)2π2E−−−−−−−√=0.961
For buckling class "a", the imperfection factor, α = 0.21
ϕz=0.5[1+α(λz-0.2)+λ2z]=1.042ϕz=0.5[1+α(λz−0.2)+λ2z]=1.042
χz=1ϕz+√ϕ2z-λ2z=0.692χz=1ϕz+ϕ2z−λ2z√=0.692
So, as per Cl. 7.1.2.1 of IS 800:2007, fcdz=min(χzfyγm0,fyγm0)=157.3 MPafcdz=min(χzfyγm0,fyγm0)=157.3 MPa
Therefore, axial compression capacity for both axes: Pdz = Axfcdz = 147.3 kN
The critical ratio for axial compression is 0 (i.e., no compression).
Check Shear Capacity
As per Cl. 8.4.1.1 of IS 800:2007, the shear area, Avz = 2×Ax / π = 7.054 cm2
So, as per Cl. 8.4.1, Vpz=Avzfyw√3=101.8 kNVpz=Avzfyw3√=101.8 kN
Hence, shear capacity along major axis: Vdz=Vpzγm0=92.56 kNVdz=Vpzγm0=92.56 kN
Shear force along both axes = 3 kN.
Critical shear ratio along both axes: 3 / 92.56 = 0.032
Check Bending Capacity
Since the section has been classified as "plastic", βb = 1.
Actual shear force in both axes, V = 3 kN < 0.6Vd = 55.53 kN. Hence, the section is subjected to low shear.
βbZpyfyγm0=7.861 kN·mβbZpyfyγm0=7.861 kN⋅m
1.5Zefyγm0=8.925 kN·m1.5Zefyγm0=8.925 kN⋅m
So, the governing bending strength with respect to the minor axis is Mdy = 7.861 kN·m
Actual bending moment about the minor axis is Mz = 4.5 kN·m.
The critical bending ratio in the minor axis is 4.5 / 7.861 = 0.572
Check Combined Interaction of Axial Compression and Bending
Section strength calculation as per Cl. 9.3.1:
n = N / Nd = 0.004
Hence, from Table 17:
α1 = 2
α2 = 2
| Mndy = Mdy = 9.341 kN·m | (Cl. 9.3.1.2(c) ) |
1.04·Mdz·(1 - n1.7) = 8.175 kN·m > Mdz
Mndz = Mdz = 7.861 kN·m
(MyMndy)α1+(MyzMndz)α2=(4.57.861)2+(4.57.861)2=0.655(MyMndy)α1+(MyzMndz)α2=(4.57.861)2+(4.57.861)2=0.655
Overall member strength in bending and axial compression
Meff=Mz-ψFxZezAx=4.5-1.0×10×26.2311.08×102=4.264 kN·mMeff=Mz−ψFxZezAx=4.5−1.0×10×26.2311.08×102=4.264 kN⋅m
Meff / Mdz = 4.263 / 7.861 = 0.542
The loading and section is the same in both axes.
Results
| Result Type | Reference | STAAD.Pro | Difference | Comments |
|---|---|---|---|---|
| Slenderness ratio | 86.46 | 86.67 | negligible | |
| Tension capacity, gross yielding (kN) | 251.8 | 252.273 | negligible | |
| Tension capacity, rupture of critical section (kN) | 297.8 | 298.368 | negligible | |
| Axial compression capacity about both axes (kN) | 174.3 | 174.338 | negligible | |
| Shear capacity in both axes (kN) | 92.56 | 92.723 | negligible | |
| Ratio for shear | 0.032 | 0.032 | none | |
| Bending capacity about both axes (kN·m) | 7.861 | 7.864 | negligible | |
| Ratio for bending about both axes | 0.572 | 0.572 | none | |
| Ratio per Cl. 9.3.1.1 | 0.655 | 0.655 | none | |
| Ratio for both axes per Cl. 9.3.2.1 | 0.542 | 0.542 | none |
Table 1.
STAAD.Pro Input
The file C:\Users\Public\Public Documents\STAAD.Pro 2023\Samples\Verification Models\09 Steel Design\India\IS 800 2007 LSD - Pipe - Tension and Bending.STD is typically installed with the program.
The following design parameters are used:
- The default value of
ALPHAis used. - The default values of
KYandKZare used. - The default value of the maximum allowable slenderness ratio,
MAIN, of 180 is used. - The default value of Ψ.
- The beam type is a cantilever, specified by
CAN 1 - The beam is laterally supported, specified by
LAT 1
STAAD SPACE
START JOB INFORMATION
ENGINEER DATE 29-Jul-20
END JOB INFORMATION
*****************************************************************************
*This problem has been created to validate the program calculated design
*results of laterally supported pipe section subjected to axial tension and
*biaxial bending, designed using IS 800 2007 (LSD)
*****************************************************************************
INPUT WIDTH 79
SET SHEAR
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 3 0 0;
MEMBER INCIDENCES
1 1 2;
DEFINE MATERIAL START
ISOTROPIC STEEL
E 2.05e+08
POISSON 0.3
DENSITY 76.8195
ALPHA 1.2e-05
DAMP 0.03
TYPE STEEL
STRENGTH RY 1.5 RT 1.2
END DEFINE MATERIAL
MEMBER PROPERTY INDIAN
1 TABLE ST PIP1016L
CONSTANTS
MATERIAL STEEL ALL
SUPPORTS
1 FIXED
LOAD 1 LOADTYPE Dead TITLE LOAD CASE 1
JOINT LOAD
2 FX 10
MEMBER LOAD
1 UNI GY -1
1 UNI GZ -1
PERFORM ANALYSIS
PRINT ANALYSIS RESULTS
PARAMETER 1
CODE IS800 LSD
CAN 1 ALL
LAT 1 ALL
TRACK 2 ALL
CHECK CODE ALL
FINISH
Copy to clipboard
STAAD.Pro Output
STAAD.PRO CODE CHECKING - IS-800-2007-LSD (V2.2)
****************************************************
|----------------------------------------------------------------------------------|
| Member Number: 1 |
| Member Section: ST PIP1016L (INDIAN SECTIONS) |
| Status: PASS Ratio: 0.655 Critical Load Case: 1 Location: 0.00 |
| Critical Condition: Sec. 9.3.1.1 |
| Critical Design Forces: (Unit: KN METE) |
| FX: -10.000E+00 T FY: 3.000E+00 FZ: 3.000E+00 |
| MX: 0.000E+00 MY: -4.500E+00 MZ: 4.500E+00 |
|----------------------------------------------------------------------------------|
| Section Properties: (Unit: CM ) |
| AXX: 11.100E+00 IZZ: 133.000E+00 RZZ: 3.462E+00|
| AYY: 7.066E+00 IYY: 133.000E+00 RYY: 3.462E+00|
| AZZ: 7.066E+00 IXX: 266.000E+00 CW: 0.000E+00|
| ZEZ: 26.181E+00 ZPZ: 34.600E+00 |
| ZEY: 26.181E+00 ZPY: 34.600E+00 |
|----------------------------------------------------------------------------------|
| Slenderness Check: (Unit: KN METE) |
| Actual Length: 3.000E+00 |
| Parameters: LZ: 3.000E+00 LY: 3.000E+00 |
| KZ: 1.000 KY: 1.000 |
| Actual Ratio: 86.67 Allowable Ratio: 400.00 LOAD: 1 |
|----------------------------------------------------------------------------------|
| Section Class: Plastic; Flange Class: Plastic; Web Class: Plastic|
|----------------------------------------------------------------------------------|
STAAD SPACE -- PAGE NO. 7
STAAD.PRO CODE CHECKING - IS-800-2007-LSD (V2.2)
****************************************************
|----------------------------------------------------------------------------------|
| Member Number: 1 |
| Member Section: ST PIP1016L (INDIAN SECTIONS) |
|----------------------------------------------------------------------------------|
| Tension: (Unit: KN METE) |
| Parameters: FYLD: 250.000E+03 FU: 420.000E+03 |
| NSF: 1.000 ALPHA: 0.800 |
| Yielding : Design Force: 10.000E+00 LC: 1 |
| Capacity: 252.273E+00 As per: Sec. 6.2 |
| Rupture : Design Force: 10.000E+00 LC: 1 |
| Capacity: 298.368E+00 As per: Sec. 6.3 |
|----------------------------------------------------------------------------------|
| Compression: (Unit: KN METE) |
| Buckling Class: Major: a Minor: a As per:Cl. 7.1.2.2 |
| Major Axis: Design Force: 0.000E+00 LC: 0 Loc: 0.000 |
| Capacity: 174.338E+00 As per: Sec. 7.1.2 |
| Minor Axis: Design Force: 0.000E+00 LC: 0 Loc: 0.000 |
| Capacity: 174.338E+00 As per: Sec. 7.1.2 |
|----------------------------------------------------------------------------------|
| Shear: (Unit: KN ) |
| Major Axis: Design Force: 3.000E+00 LC: 1 Loc: 0.000 |
| Capacity: 92.723E+00 As per: Sec. 8.4 |
| Minor Axis: Design Force: 3.000E+00 LC: 1 Loc: 0.000 |
| Capacity: 92.723E+00 As per: Sec. 8.4 |
|----------------------------------------------------------------------------------|
| Bending: (Unit: KN METE) |
| Parameters: Laterally Supported KX: 1.00 LX: 3.000E+00 Cantilever |
| Major Axis: Design Force: 4.500E+00 LC: 1 Loc: 0.000 |
| Capacity: 7.864E+00 As per: Sec. 8.2.1.2 |
| Minor Axis: Design Force: -4.500E+00 LC: 1 Loc: 0.000 |
| Capacity: 7.864E+00 As per: Sec. 8.2.1.2 |
|----------------------------------------------------------------------------------|
| Combined Interaction: |
| Parameters: PSI: 1.00 CMX: 0.900 CMY: 0.900 CMZ: 0.900 |
| Section Strength: Ratio: 0.655 As per: Sec. 9.3.1.1 |
| LC: 1 Loc: 0.000 |
| Overall Member Strength (Bending+Tension): |
| Equation 1(Z): Ratio: 0.542 As per: Sec. 9.3.2.1 |
| LC: 1 Loc: 0.000 |
| Equation 2(Y): Ratio: 0.542 As per: Sec. 9.3.2.1 |
| LC: 1 Loc: 0.000 |
|----------------------------------------------------------------------------------|
| Checks Ratio Load Case No. Location from Start( METE) |
| |
| Tension 0.040 1 0.000E+00 |
| Compression 0.000 0 0.000E+00 |
| Shear Major 0.032 1 0.000E+00 |
| Shear Minor 0.032 1 0.000E+00 |
| Bend Major 0.572 1 0.000E+00 |
| Bend Minor 0.572 1 0.000E+00 |
| Sec. 9.3.1.1 0.655 1 0.000E+00 |
| Sec. 9.3.2.1 (Z) 0.542 1 0.000E+00 |
| Sec. 9.3.2.1 (Y) 0.542 1 0.000E+00 |
|----------------------------------------------------------------------------------|
Parent topic: V. India
| Related concepts |
|---|
| D8.A.2 Design Process |